Drill Rigs For Sale

Plastic 10,000LTR Tanks (POA) (sale-ehub896)

Condition: Good Exterior Colour: Aqua/Green Total Tank Capacity: 10,000L

Price : POA

Gardner Denver Grey Pump (POA) (sale-ehub895)

Make: Gardner Denver Condition: Good Exterior Colour: Grey

Price : POA

Blue Skid Mounted on 10,000LTR Tank and Pump (POA) (sale-ehub894)

Condition: Good Exterior Colour: Blue Total Tank Capacity: 10,000L

Price : POA

2011 Atlas Copco Pumpac Mud Pump (POA) (sale-ehub893)

Atlas Copco Craelius Pumpac Mud Year: 2011 Condition: Good Exterior Colour: Yellow

Price : POA

2011 Atlas Copco Mustang Tracked Drill Rig (POA) (sale-ehub982)

Year: 2011 Condition: Good Hours: 3582 Exterior Colour: Yellow Location: Queensland, Australia

Price : POA

Land Liner (POA) (hire-ehub891)

Polypropylene composite consists of three barrier films sandwiched by double layers of needle punched geotextile with heat fused surfaces 2 x more tear resistant and 4 x more puncture resistant than standard 30-mil HDPE liners High-traction surface minimises slip and fall injuries, even when covered by hydrocarbon spills Absorbs and contains nuisance leaks, drips and spills on contact; embedded barrier film helps prevent major spills from reaching the ground Tough seams won't pull apart when driven over by trucks or even track hoes Weldable and sealable for easy installation and patching 100% recyclable and incinerable to reduce waste

Price : POA

Storage Tank (500BBL) (POA) (hire-ehub890)

Total tank capacity: 79.5kL (500BBL) Road trainable Full-size submarine access door into tank Ladder accessible viewing platform to observe inflows and fluid heights Sight glass fluid level indicator Sunken suction sump with strainer grate Rugged 200 x 100 RHS perimeter frame 6mm crimped walls, 10mm floors Tandem axle, leaf spring suspension Internal surfaces coated with corrosion resistant paint *For any additional information, please contact us*

Price : POA

Poor Boy Degasser 10 inch

2 beam with 2" NB pipe end rolls and 200 x 100 fork slippers 1 x 2 " Fig1502 entry from choke manifold Open bottom with fluid seal Zone mapping provided Total mass: 800kg Total tank volume: 1500L Fluid volume: 50L Plumbing: 1 x 2 " camlock suction point from sunken sump in main tank 1 x 2 " camlock suction point in fluid seal tank 2 " Diesel Transfer pump complete with 15 metres of suction hose and spark arrestor *If any more information required, please contact us*

Price : POA

SEG 2600 Rig (POA) (sale-ehub883)

Rotary Drilling Rig Machine w/ capacity for direct, inverse circulation and DTH system Model: SEG 2600 Engine: Caterpillar C15 Capacity Drill 2.000 meters of depth with 8 1/2" of diameter 30" of diameter until 500 meters depth Total pull up capacity: 100 T Uses 2 Hydraulic cylinders and chains Unit is fully Hydraulics Easy to change from direct circulation to reverse circulation Easy handling for operator *TRAILER IS NOT INCLUDED IN PRICE* *For more information/details, please contact us*

Price : POA

Gallagher 600 HDD Drill Rig ($500,000) (sale-ehub882)

Year: 2003 Hours: 6,200 Push/Pull Capacity: 600,000LBS Engine: Cummins QSX19 Power: 800HP Drill Length: 52ft Carriage Travel: 44ft Trailer Mounted: Gallagher Quad-Axe Rig Capable of: High Speed: 70RPM / 20,000FTLBS Rotary Torque Low Speed: 25RPM / 82,000FT Rotary Torque Drillers Control Box is fitted with: - Lockable Door - Split System Air Conditioner - Desk - 240V Power Receptacles - 10 Controls *For more information/details, please contact us*

Price : $500,000

Gallagher 400 HDD Drill Rig ($400,000) (sale-ehub881)

Year: 2002 Hours: 18,940 Engine: Cummins QSX15 Power: 600HP Drill Length: 52ft Carriage Travel: 44ft Trailer Mounted: Gallagher Tri-Axle Push/Pull Capacity: 400,000LBS Rig Capable of: High Speed: 100RPM / 28,000FTLBS Rotary Torque Low Speed: 40RPM / 56,000FT Rotary Torque *Complete tear down and rebuild 2015* Drillers Control Box fitted with: - Lockable Door - Split System Air Conditioner - Desk - 240 Power Receptacles - 10 Controls *For more information please contact us*

Price : $400,000

2008 Boart Longyear Delta Base 102 Drill Rig (POA) (sale-ehub880)

2008 Boart Longyear Delta Base 102 Drill Rig Condition: Poor Location: Victoria

Price : POA

UDR650 Drill Rig (POA) (hire-ehub879)

UDR650 Drill Rig

Price : POA

UDR650 Drill Rig (POA) (sale-ehub878)

UDR650 Drill Rig

Price : POA

DR800 MK II (POA) (hire-ehub877)

DR800 MK II Drill Rig

Price : POA

DR800 MK II (POA) (sale-ehub876)

DR800 MK II Drill Rig

Price : POA

Geotechnical Drill Rig ($25,000) (sale-ehub875)

New Holland Drilling Rig, deisel motor on Hino 4WD 7 ton Truck. 14 x 3mtr length drilling rods. High pressure FMC pump and water injection pump; 5 mtr mast. KMs: 1234 Year: 1986 Make: Hino Truck Type: Drill Rig

Price : $25,000

Boart Longyear 850 Multipurpose Top Head Drive Drill Rig ($245,000 ex GST) (sale-ehub874)

Has on board air with a Sullair 900cfm 350 psi compressor mounted on the deck Carrier is a 1983 MAN twin steer with 128,222 kms on the odometer Drill Rig has 8,989 hrs on it Compressor has 5,464 hours although the air end was overhauled 100 hours ago. The multipurpose rig has been well maintained, Minespec’d and was re-hosed with burst protection sleeving fitted approx. 1000 hours ago. The unit is currently registered in NSW. Suitable for coring, large diameter and water boring drilling Can fit 14 inch through the table Condition: Excellent

Price : $220,000

2000HP Drill Rig ($USD8.975 Million)(sale-ehub818 )

This 2000HP rig is Chinese constructed with all relevant certifications. It also come with USA made Cat 3512B engines. The rig was originally manufactured for a drilling company who in the end sold out of the business but, retained the new rig as it was not yet completed when the business was disposed of. The owner is ready to stand the rig up for inspection and carry out any minor faults that might appear as the rig has been stacked for a couple of years. Due to the fact that most components for the rig were from third party manufactures, there is no longer any warranty honoured. This is the main reason why the equipment is reduced in price down to 8.975 million from its original cost exceeding 12.0 million USD. There has been strong interest in the rig, if the owner was prepared to convert the F1600 pumps up to a working pressure of 7500PSI which they are not prepared to do for understandable reasons. To have this equipment built now would cost in the region of 13.0 million and a waiting time of twelve months or more. Full specifications available upon request

Price : $USD8,975,000

2011 Sandvik DE710 Drilling Rig ($USD315,000)(sale-ehub817)

Sandvik DE710 Drilling Rig 2011 model 1900 hours John Deer engine Strickland tracks undercarriage is in great condition

HH 75 MAST EXTENSION (POA) (sale-ehub695)

FRAME WORK IS IN PIECES IN TWO SECTIONS IN BONEYARD

Price : POA

DB1000 Drill Rig and International T line 8x4 carrier (sale-ehub816)

DB1000 Drill Rig and International T line 8x4 carrier 1989 Model VIN : 6F2FK2600KDV11039 FMC mud pump Compressor Various Drill pipe Jack Legs

Price : $57,500

Eziprobe Drill Rig mounted on Land Rover Defender (sale-ehub593)

Eziprobe Drill Rig mounted on Land Rover Defender (2003) Rego 1GRJ871 ODO 311000 klms This drill rig is a highly versatile unit capable of multiple drill techniques. It is ideally suited both on and off-road for use in shallow (up to 10m depth) geotechnical, environmental or exploration investigations. The EVH manufactured ‘Eziprobe’ drill is mounted on a 2003 4WD Land Rover Defender fully licensed. Included • • Air Compressor fitted (for tyres. Not for drilling) • • Karcher pressure washer • • 50l water tank fitted • • 2000W Inverter fitted • • 50mm Towbar • • UHF Radio • • Spotlights • • Extended range Fuel Tank • • Reversing Camera • • Aluminium Toolboxes • • Hydraulics run from PTO on transfer case • • No tooling, augers included

Price : $54,950

Australian Corig Mounted on 2012 Man 8x4 Truck ($USD445,000)(sale-ehub682)

The truck has only 980 Hrs of operation and 9706.1 Km. Excellent condition RIg Spec MAST Height -16.5m Maximum capacity - 22,680kgs GRIPPER Maximum capacity -11,340kgs Rod trip rate -30/min HOOKLOADS Maximum capacity - 22,680kgs MISCELLANEOUS 3 in , rod blowout preventer rating - 3,000psi Rig-in/out time - 30 min saftey equipment - yes

Price : $USD445,000

CE180 DRILL RIG (sale-ehub638)

DRILL RIG: - CE180 - 1200 hours on the clock with regular servicing - 900 mm wide - 2.85 m high when operating - 1.5 Ton pull Back - 1800 Nm Low gear (75 RPM) - 500 Nm High gear (400 RPM) - 2.2 m head stroke - Mast extensions to pull 3 m - 500 KG winch - Hydrapower Automatic SPT - Bourne Under head Swivel - Silvan BP121 Coring Pump - Max Depth is 60 m - 7 Ton Atlas Hydrulaic Hammer for Push Tube Sampling - Capable of up to 300 mm auger Trailer: - 6 Ton Plant trailer - Setup specifically for tight access rig - 12” disc brakes - regular servicing - Rego until October 2019 Drilling Gear - 15 m 3.5” augers - 15 m MHJR Rods (70 mm) - 15 m HQ Rod - 1.5 m NMLC Barrel - All drive subs needed - A-Frames - Push Tube Sampling Subs - Aluminium mud tank

Price : $136,500

2x Schramm T130XD Drill Rigs (2x units to choose from, buy one or both) (OPEN TO OFFERS)(sale-ehub67

2x Schramm T130XD Drill Rigs (2x units to choose from, buy one or both) The Schramm T130XD is a heavy duty, heavy hoist, carrier mounted drill rig. The T130XD utilizes the latest concepts in mast design and technology. Telescoping construction permits long head travel and working height to allow use of Range III casing, yet short overall length in the transport position. With a front overhang of less than 6 feet, the T130XD will get you to the jobsite when access roads require a compact machine. Heavy pullback capacity makes this machine a perfect choice for shallow oil and gas, coal bed methane drainage and deep water well applications. • 130,000 lbs. (59,090 kg) actual pullup • 28 inch (711 mm) table opening • 760 hp deck engine • 1350/350 – 1150/500 variable volume compressor • (38 cu. m/min @ 24.1 bar & 32.6 cu m/min @ 35.5 bar) • 50 feet (15.25 m) of clear head travel • Range III casing Located: Australia Condition: Work Required Price: OPEN TO OFFERS

UDR1000 - 8x8 MAN 34-402 Carrier (sale-ehub653)

Year - 1997 model UDR1000 Carrier - 8x8 MAN 34-402 Head has been rebuilt Hyd pumps rebuilt Tri drive funk box rebulit New fire suppression New radiator in carrier Mast needs some work. Hours unknown Carrier is in mint condition

Price : $195,000

Dynatech tracked Drill rig (POA)

Dynatech tracked Drill rig (POA)

Price : POA

Mole Pioneer drill Rig on ford 6x4 carrier (POA)(sale-ehub649)

Mole Pioneer drill Rig on ford 6x4 carrier POA

Price : POA

3 x Hydrapower HP850 Drill Rigs For sale $875,000 +GST each (sale-ehub631)

Hydrapower HP850 Drill Rig Serial No HP850-59 Year of Manufacture 2010 Engine no 87854376 Current Meter Reading 1072 Hours Mercedes Actros 4144 Rig Truck Year of Manufacture 2010 Vin no WDB9323362L469846 Engine no 54197700696468 Current Meter Reading 10670 KM BQ to 1500m NQ to 1250m HQ to 850m PQ to 550m Rotary Mud to 300m Hammer to 300m Price @$AUD875,000 ex GST Asset No – 1286 Drill Rig – Hydrapower HP 850 Serial No – HP850-61 Current Meter Reading – 3957 Hours Year Model – 2011 Asset No – 4086 On Board Compressor – Sullair DXHDLOFT 1150XI350 Serial No – 200802290047 Current Meter Reading – 1000 Hours Year Model – 2011 Asset No – 6186 Rig Truck – Mercedes Benz Actros 4144 Vin No – WDB9323362L484255 Current Meter Reading – 12770.00 KMS Year model – 2010   Asset No – 1288 Drill Rig – Hydrapower HP 850 Serial No – HP850-59 Current Meter Reading – 1072 HRS Year Model - 2011 Asset No – 4088 On Board Compressor – Sullair DXHDLOFT 1150XI350 Serial No – 200804030050 Current Meter Reading – 500 Hours Year Model – 2011 Asset No – 6188 Rig Truck – Mercedes Benz Actros 4144 Vin No – WDB9323362L469846 Current Meter Reading – 10670.00 KM Year model – 2010   Asset No – 1289 Drill Rig – Hydrapower HP 850 Serial No – HP850-64 Current Meter Reading – 3800.90 Hours Year Model - 2011 Asset No – 4089 On Board Compressor – Sullair DXHDLOFT 1150XI350 Serial No – 201011080061 Current Meter Reading – 1746 Hours Year Model – 2010 Asset No – 6189 Rig Truck – Mercedes Benz Actros 4144 Vin No – WDB9323362L485070 Current Meter Reading – 10436.00 KM Year model – 2010   BQ to 1500m NQ to 1250m HQ to 850m PQ to 550m Rotary Mud to 300m Hammer to 300m

Price : $875,000

2 x XDL-5B drill rigs, with a mountain of spares(sale-ehub629)

• 2 x XDL5B drill rigs, • Under 10 hours on each machine • Comes with a mountain of spares from drill pipe to bits reamers chuck jaws bearings etc • Barrels and tubes • 760mts HQ pipe • 1500mts NQ pipe $280,000 for the full package

Price : $280.000

Boart Longyear BLY LS600 Sonic drill rig & TSV Tracked Carrier IHI IC70-2 (Package)(sale-ehub622)

Boart Longyear BLY LS600 Sonic drill rig & TSV Tracked Carrier IHI IC70-2 (Package) Drill Hours - 7302, TSV Carrier Hours - 422 Head – BL150 (PS150 head) Rebuilt – February 2018 – Bearings and seals Additional to Factory (upgrades) Main Winch Limiter Service Winch Limiter Carrier Slope and over run warnings Automatic/Manual activated 60l fire suppression Hydraulic catwalks Hydraulic rear deck Rotation spindle lock Reverse Camera Work Lights Condition: Excellent Located: Australia Package Price @$657,500 ex GST

Price : $657,500.00

Track Mounted UDR1000(sale-ehub605)

Track Mounted UDR1000 C/W Rod Handler, new ropes, certs, fully operational Remote controlled track base Condition: Great Location: Western Australia

Price : 550,000.00

Schramm T660 RC/AC Drill Rig with 1988 MAN 8x4 Truck(sale-ehub604)

Drill Rig Specification Drilling Method: Reverse Circulation Rig Engine: 60 Series Detroit Drill Rig engine hours 4152 hrs Compressor: Sullair 900 CFM / 350PSI, 2179hrs Hammer oiler Pull Back 40,000lb (18,000kg) Drilling Depth Vertical: 400m Drilling Angles: 55 to 90 degrees Drill Rod Specifications: 4.5 inch x 6m Mast Specification Sandvik DA554 Hands free rod loader Direct hydraulic control arm Top Rod centralizer Dual lower rod spanners Below head air swivel Above head deflector 4.5 inch slips table Hurricane Booster 750psi Booster hours 1506hrs CAT Dust Suppression water pump Condition: Good Location: Western Australia

Price : $295,000.00

Hydrapower Explorex 800 Drill Rig(POA)(sale-ehub603)

Hydrapower Explorex 800 Drill Rig The Explorer 800 is the bigger brother of our Explorer range and comes complete with all of the drilling capacity that you are likely to need in the harshest of environments. The 6 cylinder Cummings diesel unit with after cooler delivers an impressive 176 horse power at 2500rpm. With a main winch line pull of 8000kg, you will have all of the drilling power that you are likely to need. Rig Engine - 6 cylinder Cummins CPAK-6BTA turbo after cooled with 176hp at 2500rpm Rig Hydraulics - Sauer Danfoss proportionally controlled control valves. Sauer closed loop pump on rotary drive. Sauer open loop pump on auxiliary functions Rotary Drive Hydrapower Gearbox — Steel Casing with floating hollow spindle and hydraulic head lock and swing. Two Speed, 0 –225rpm & 0–966rpm low speed torque to 4150Nm, high speed torque to 966Nm Head Travel 6.8m Main Winch Maximum pull is 8000kg. Maximum line speed is 60m/min Wireline Winch (1) One of in standard configuration. Maximum pull is 780kg. Maximum line speed is 83m/min Pulldown Electrically controlled with dial for speed control. Pull down capacity is 7000kg. Pull out capacity is 11500kg Mast - Fitted with 2.0m mast dump for angle drilling. Standard length is 10m, supplied with hydraulically operated breakout spanner and top pulley swivel. Supplied with hydraulic circuit with quick-connect couplings for optional breakout table Condition: Good Located: Victoria Price: POA

Price : POA

Geoprobe 6620 DT(sale-ehub591)

Geoprobe 6620 DT (2004) Approx. 5000 Hours This unit is a fully hydraulic, rubber track mounted mobile remote-controlled drill rig equipped with a very powerful hydraulic hammer with built in rotary spindle for concrete drilling and anchoring, over 20 ton pulling capacity. Included • • 200 litre PVC water tank fitted • • Karcher pressure washer and mount • • 2000W Inverter fitted • • 50mm for towing trailers onsite • • No tooling, augers included Specs https://probetechnologiesinc.com/machines/m6620dt-specs/

Price : $54,950

Comacchio P450 (sale-ehub585)

Comacchio P450 Capabilities • HQ: 500 Metres • Open Hole: 350 Metres • Pull Back: 10,500kg • Mass: 11,500kg Safety • 3 x Emergency Stops • 1 x Remote Emergency Stop • Interlock Safety Cage Lockout Switch • Remote Control Movement • 4 x Stabiliser legs Additional information • Steel Track Base with Rubber Inserts • Speed 4km/hr • 4 x Winches • Ground Pressure 0.49kg/cm² • C16 Mono Pump • W11 Bean Pump Rig also has complete Metzke / Mincon RC Setup with available for extra cost

Price : $197,500.00

Multi Purpose Boart Longyear LX6 Rig (sale-ehub575)(POA)

Multi Purpose Boart Longyear LX6 Rig for Sale. 2018 model with only 638 hours. Practically brand new, perfect working condition. Multipurpose geotechnical rig capable of wireline and conventional coring, as well as DTH, rotary and auger drilling methods up to 350m

Price : POA

SANDVIK PANTERA DI 6400(sale-ehub576)

Drill rig SANDVIK Type: PANTERA DI 6400 Year: 2014 Engine hours: 5.480 Drill hours: 2.680 Compressor hours: 2.950 Weight: approx. 37,0 t - air conditioner - independent vehicle heater - compressor SULLAIR 20/12 - engine CUMMINS QSX 15 with 399 kW

Price : $365,000.00

Boart Longyear LM90 drill rig(sale-ehub574)

Boart Longyear LM90 drill rig 2007 Model 9896 Hours It also has a spare rotation head and winch that goes with it

Price : $85,000.00

Boart Longyear LM110(sale-ehub573)

2015 model, Brand new It has never had a rod in it and always stored under cover in a warehouse It was and is all set up for a demo to see it running if you would like to inspect the unit.

Price : $550,000.00

UDR 1500 (sale-ehub569)

UDR 1500 Model No.1500 Serial No. 1500-11

Price : $149,500

Kempi air operated diamond rig underground(sale-ehub557)

Kempi air operated diamond rig underground 1990 model Complete setup inc rods and trailer

Price : $17,500.00

LONGYEAR LY850 (POA)(sale-ehub556)

• LONGYEAR LY850 S/N GK850-017 • CUMMINS ENG • FMC BEAN MUDPUMP – Hyd Drive Model W1122BCD • PULLMASTER WINCH MAN year 1981 – last registration to 16.6.14 • VIN38600090009 • Eng No. 3283533047311 • KMS 192000

Price : POA

Geotechnical Trailer Mounted Drilling Rig - EVH 1750 Rotation Head on EVH 2100 Mast Trailer Drill Ri

Geotechnical Trailer Mounted Drilling Rig - EVH 1750 Rotation Head on EVH 2100 Mast Trailer Drill Rig Capabilities:- • Wash bore - (King 2J water swivel) • Auger • SPT • U50 • 3 cylinder diesel engine - Currently on dual axle braked trailer (with tool boxes, rod racks, alloyed mud tanks fitted to trailer) - Rig can do 3m lift with winch and just gets 3m lift with head (is easier with a short kelly bar) - Not a dump mast. Pivots off back of trailer - Rig has been modified to suit various uses. Can be taken off the trailer and manoeuvred (quick hitch attachment) and powered by an excavator and set up on legs (some pics attached). - Some factory EVH parts (still basically 2100R spec) but generally a bitsa, over $25K spent since 2015 on upgrades from the original EVH spec. . - It can do diamond drilling, auger, washbore as well as SPTs - It requires separate mud pumps (not included) - We purchased it in May 2015, my understanding it was a new engine recently so I'd expect <100 hrs now - Good Condition - Located: Brisbane, Queensland Make an offer

Price : $10,000

Bournedrill 1000 THD(sale-ehub544)

Bournedrill 1000 THD Cat C11 Deck engine Man 2008 TGA 8X8 Truck Rig hrs 13539 Truck klm 44958 Good condition all round all service history available 18000 kg pull down Udr foot clamp assy Dump mast 4 speed head Bean pump FMC W1122B Triplex Condition: Good Located: New South Wales Price $707,000 ex GST

Price : $707,000 $667,000

2011 Boart Longyear LM90 with 150HP electric motor fitted (LM110). (sale-ehub536)

• 2011 Boart Longyear LM90 with 150HP electric motor fitted (LM110). • Includes supply of spare 110HP electric motor, all manuals and spare parts • Approx 700 hours • 1.5m feed frame (5 ft) • 150 HP motor SN# WWHT150-18-445TC • Skid SN#LMFP-815 • Head SN# LMF-1182 • Boart Longyear Rod Handler SN#LMRH-139 • 90 KW Electric Motor SN# 0601-227320-1

Price : $450,000.00

3 x Sandvik D45KS drill rigs for sale (POA)(sale-ehub534)

3 x Sandvik D45ks Drill rigs for sale Various condition All rigs have not operated for 12 months Located in west africa prices range from USD 300-400k

Price : poa

Straight line 2420 modified, small rotary rig, mounted on Canter 4x4 Carrier(sale-ehub516)

Straight line 2420 modified, small rotary rig, mounted on Canter 4x4 Carrier 3.5m stroke 1.4m dump mast 12,000 pound pull back Hours: 1100hrs Mounted on 4x4 canter Condition: Very Good Price @$165,000 ex GST

Price : $165,000.00

Boart Longyear manufactured GK850 on a 2000 model Iveco MP4500 8x4 Carrier(sale-ehub509)

Boart Longyear manufactured GK850 on a 2000 model Iveco MP4500 8x4 Carrier The rig was originally a Boart Longyear manufactured GK850 (unknown date of manufacture) that underwent a rebuild in 1997 to the current format. The machine has drilled to 1000m NQ2 whilst I have owned it, it is fully functional and ready to go to work. The rig is licenced in WA, in excellent running condition and has been working up until I pulled it out for sale. Reason for sale is that I have upgraded to another machine. I have a comprehensive maintenance schedule available with the following recent repairs of particular note: • New Wireline Drum and Motor fitted • Recent rebuilt and upgraded drill head by Austex Engineering • Recent FMC mud pump overhaul • Pull Down Sheave wheels refurbished with new bearings • Rope certification certificates available • Rod Spinner recently refurbished Rig has the following features: • Rod Spinner • Rap-Span Breakout • Hydraulic rotation lock out cage • Custom fold down ladders • Custom Safety Rails (with opening gates) • Rod Box • 9m Rod Pull • 1500L rig fuel tank • Custom Work Platform • Emergency Stops • Hydraulic Foot Clamps • Driller control panel overhead protection Condition: Excellent Hours: 6275 (indicated) Located: WA Price: $159,500 ex GST (firm)

Price : $159,500.00

Boart Longyear KWL1600 with Sullair 1350XH package £395,000(sale-ehub504)

Boart Longyear KWL1600 with Sullair 1350XH package Rig year 2008 Hours 7,189 Cat C13 Tatra truck year 2007 Sullair year 2010 Hours 111 Mounted on a 2012 Man 4x4 Needs to be sold as a package Price £395,000 Ex UK

Price : £395,000

Boart Longyear LF90D £200,000 (sale-ehub503)

Boart Longyear LF90D 3000hrs 2013 on tracks £200,000 Recently used in UK, good condition – Some spares

Price : £200,000

Sparr Drill rig mounted on western Star truck(sale-ehub493)

Sparr Drill rig mounted on western Starr truck 1995 Western Starr 4964F; Km’s 7707817; engine hours 96024. Drill rig hours – 324.16. Elgi hours – 2133.90 Various drill pipe and accessories

Price : $350,000.00

SANY SR150C x2 ($USD295,000.00) each

2 unused SR150C Year 2013 south America Both get full warranty from. SANY Both have CE marking SANY WILL SUPPORT IN ALL MATTERS AND QUESTIONS IF NEEDED

Price : $USD295,000.00

Maxi 400 RC Rig with Compressor and Booster including Inventory($USD1.3m)

DESCRIPTION STOCK 1.- MAXICAT DRILL RC 1 mastlength 9.85 meters track length 4.70 meters width 2.02 hwight mast down 3.50 meters ground level 2.- SULLAIR COMP CARRIER 1 8 meters long 3 meters wide 3.60 meters higt ground level sullair compressor ATLAS COPCO BOOSTER STOCK 1 1/2 whip chechs for air hoses 6 15 meters 1/2" alpha goma oir hose 2 5 meter 1 1/2" alpha goma air hose 2 gates belt k080415 john deere fan booster new 1 FF5421 fuel filter fleetguard new 1 LF 3970 lube filter fleetguard new 1 P55042 lube filter donalson new 1 LF 16243 lube filter fleetguard new 1 re 504836 john deere oil filter new 1 jic 1 1/2 plugs for air hose 2 jic 1 1/2 male fihings to join air hose 2 MATRIX STOCK DESCRIPTION NEW USED drill pipe M4 in guad drill pipe, M4 frit x 3 meter (with field replaceable inner tube) 156 drill collar, M4 x 3 meter, baker lock 4.65 OD 1 drill collar inner tube M4 x3 meter 1 inner tube tester m4 1 SW casing 3 meter lehgth 4 M4 reamer 1.5 meter lenggth hard pads @ 4 1/2" OD 3 bleeder sub with inner tube M4 1 interchange, 2 slot jetted 1 M4 wrench key table 2 center tubes for starting rod matrix 2 adaptor sub, M4 box to PW casing pin 1 adaptor sub, M4 box to SW casing pin 1 rock bit adaptor inner tube 2 rock bit wera sleeve M4 5" rock bit wera sleeve M4 4 7/8" 1 rock bit wear sleeve M4 4 3/4" 2 2 rock adaptor ass M4 box to 2 7/8" reg box down 1 rock wera sleeve M4 4 5/8" saber sub blowdown sub with inner tube M4 1 blowdown sub M4 fishing spear 1 adaptor sub 2 7/8" reg pin to 2 3/8" box 1 back raemer inner tube for 545 hammer (made in mexico) 2 8 back raemer inner tube for halco 412 hammer (made in mexico) back reamer adaptor assemble M4 dual tube box to 4" metzke type hard parts set # 5 inch M4 drill pipe inner tunçbe x M4 1.5 meter 1 adaptor sub M4 box to 3 1/2" reg. Box 1 center tubes (made in mexico machineshop) for startin grod 3 O ring # 151 inner barrel oring 120 SW casing 1.5 meter 4 M4 frit x 3 meter innnertubes 35 back reamer 4 1/2" metzke to M$ box TRC 545 matrix 2 2 rock bit adaptor ass M4 box to 2 1/8" reg. Box down rebuilt ot machine shop 1 SW casing 3 meter length 4 3 meter inner tube for matrix collar 2012 1 1.5 meter inner tube for matrix collar 2012 2 DESCRIPTION STOCK NEW USED hammer assy 4 1/2 metzke 1 1 circlip 2 sample tube 5 18 circlip aiscreen distribuidor nozzle plunger 2 spring piston tetaiting ring 1 bit retaiting ring 2 rubber parts kit (for items 2,4,7,8,14,15)** 1 RE545 shround hrdn 5-3/16" 2 RE545 bit 5 1/2 inch 2 Re545 bit 4 3/4 inch 1 RE545 bit 5 inch 4 RE545 bit 5 1/4 inch 5 RE545 bit 6 3/4 inch (used) 1 shoround H dened 4 3/4 to 5 1/4 25 PMF545H-54 CF- 5 1/2 IN RE545 1 PMF545H-53 CF- 5 3/8 IN RE545 2 PMF545H-50CF-5" RE545 1 PMF545H-47RC-4 1/8 RE545 2 5 3/16" SHROUNDS SANDVIK 2 5 1/16" SHROUNDS SANDVIK 2 4 1/16" SHROUNDS SANDVIK 2 4 7/8 " SHROUNDS SANDVIK 1 PMF 545H- 54CF 2 PMF 545H- 53 RC 1 PMF 545H-50 DC 3 PMF545H-47 DC 2 PMF 545-46 DC 1 BACK HAMMERT FROM HOLT STOCK NEW USED SUB ADAPTORS TO M4 MATRIX PIPE FOR BACK HAMMER 1 10 METERS HYD HOSE LINCH FOR BACK HAMMER 2 HOME MADE ROCK FOR TO DRIVE WITH BABLE FOR BACK HAMMER 1 WATER DEPOSIT (SWIMMING POOL) TORP PIPE FROME 1500 LITER FOR WATER 1 HOME MADE HITCH FOR CAT RIPPER 1 HOME MADE FOR FORD 150 FOR BOOSTER 1 HALCO BIT CATCHERS PARTS STOCK QUITSIDE DIAMETER NEW USED 125.50/125.75 603960 1 4 HALCO BITS DIAMETER FACE DESING BUTTONS STOCK PART NUMBER MM INCH TYPE QTY/DIA NEW USED 53178 121 4. 3/4 CANCAVE DOMED 16X13MM 2 53179 127 5 CANCAVE DOMED 8X16MM/9X13MM 5 53177 130 5. 1/8 CANCAVE DOMED 8X16MM/9X13MM/4X14 1 53164 133 5.1/4 CANCAVE DOMED 8X16MM/5X13MM/4X14MM 1 TRICONES DESCRIPTION STOCK NEW USED 4 7/8 IN Q4DS 1 4 3/4 IN Q4DS 1 5 IN Q5DS 3 2 4 7/8 IN Q5DS 1 5 1/8 IN Q5DS 1 5 1/1 IN Q4SDS 1 5 Q4DS 1 DERCRIPTION STOCK NEW USED RE 545 BIT 7 1/2" 1 HALCO BIT CATCHERS PARTS STOCK QUITSIDE DIAMETER NEW USED 125.50/125.75 603960 1 4

Price : $USD1.3m

Ingersoll Rand DM45E

Alot of upgrades have been made. New Hydraulic motors New Traverse Cylinders New hose – complete rehose Rebuilt track motors and tensioners Track links replaced where needed Rebuilt rotation motors All oils replaced Upgraded air delivery including 2” hosing and 4J swivel sale-ehub466

Price : $275,000.00 $259,500.00

Universal Drill Rig - KL1000

Make : KL1000 Model : Universal Drill Rig Condition : Used Universal drill rig setup for diamond core. low hours on full rebuild. Tatra Terra No 1 8x8 carrier. 2008 model. Only 8000kms

Price : $375,000

2013 Corporaal Ent CE100 Tracked Drill Rig FOR HIRE (POA) (Hire-ehub819)

2013 Corporaal Ent CE100 Tracked Drill Rig John Deere: 6068TF150 turbo charged diesel engine Engine#: CD6068C039320 Chassis#: 12/547-62-1 Hydraulic Pump: Poclain Hydraulic pump- 6 Independent flows Head Motor: Hansa TMP – fixed displacement axial piston motor M3X series Hours: 55 hrs Condition: Excellent Located: Perth, Western Australia

Price : POA

Daly Bros DB1000 Multi Purpose Rig & Drilling Equipment

Rig is mounted on a freightliner Fl106 Truck -1641 Hours, 158276kms, 318hp Detroit series 50 Capacity 300m HQ, 400 -500m NQ 2 Speed Rex-roff Drill Head Motor. Speed approx.. 0-250rpm up to about 1000rpm Hyd. Open-close drill head Drill Head Travel 6.5metre 9 metre Rod pull Main Winch about 4,500kg Single Line Pull Wire line winch about 1,500 kg single line pull 2 extra winches about 500kg single line pull Angle capacity to 45 degrees 4 levelling jacks Bean W11 pump hyd. driven Perkins 6 cyl Motor about 4,000 hours with 4 drive pump box (3 being used) 2 x mud tanks DRILLING EQUIPMENT 50m plus N/taper rods - 6m, 3m, 1.50m, 0.50m 30m NW casing - 3m, 1.5m & 0.5m 3 x NMLC 3m core barrels 3 x NMLC 1.5m core barrels 1 x NMLC 3m core barrels NQ 3m &1.5m core barrels HQ 3m & 1.5m core barrels 1 x spt drop hammer 2 x spt split samplers tube adapters 50mm & 75mm Bits & subs to suit All necesary equipmentr to start geotech Drilling

Price : $132,000.00

2012 Atlas Copco Surface Mining Drill Rig DM75(sale-ehub327)($USD1.35m)

2012 Atlas Copco Surface Mining Drill Rig DM75 Technical Specifications: Metric Product series: DM series Drilling method: Rotary - Multi pass Hole diameter: 229 - 270 mm Hydraulic pulldown: 334 kN Hydraulic pullback: 133 kN Weight on bit: 34 t Maximum hole depth: 51.2 m Estimated weight: 68000kg Motor manufacturer: TECO Motor power:700HP @1458r/min Airprossor:51m^3 @758 kPa With rear-winch Depending on electric motor driving Hours: 600

Price : $USD1,350,000

Sandvik D25KS DTH Drill Rig

Sandvik D25KS DTH Drill Rig Specifications: YOM: 2015 Engine: CAT C18 Compressor: Sulair 1024CFM Machine Hours: 4890 This machine is in excellent working condition. Full maintenance history records available, fully maintained to OEM specifications.

Price : USD850,000

Hydco 500RC mounted on a Oshkosh 8x8 Carrier

Hydco 500RC (Modified) Mounted on 8×8 Oshkosh, Right hand drive, Allison Auto, Eaton Diffs, Hendrickson Suspension. • 36ton / 80000lbs pullback at 2800psi (pumps and valving on Traverse circuit good for 52000kg / 115000lbs pullback @ 4000psi) • 8m Stroke • Dump Mast • Boom winch • Survey Winch • KL Rod Handler • Air Drill Rotation Head • Cummins QSM • Rexroth A10VSO load sensing, variable displacement pumps. 4 x 252lpm, 1 x 180lpm, 1 x 130lpm • No Air Just Undergone an extensive rebuild, all new hosing. Specifications: Diesel Engine: *Cummins QSM11, In-Line 6 Cylinder, 10.8 Litres, Turbocharged, Intercooled. Hydraulics: *Rexroth A10VSO Pumps, 4x140cc, 1 x100cc, 1x71cc. Variable displacement, load sensing. Nominal Pressure Peak Pressure 4061 psi/280 Bar 5076 psi/350 Bar *Hydraulic Driven air to oil Cooler. *Walvoil Pilot Control Valves (Rotation, Traverse, Fine Feed). *Danfoss PVG32 Load Independent Proportional Valves. load sensing feedback infinitely variable. *Danfoss Rotation motors. Drill Mast: *HYDCO lattice drill mast with 160HTT chains. *8m Stroke. *Traverse Max speed up 63 meters / minute. *Hydraulic cylinder over chains 2:1 ratio. *3m mast dump. *Capable of angles from vertical to 45 degrees. *Hydraulic operated Rod guide. Rotation Head: *Air-Drill 2 speed Head (OMVW-630 Motors) Continuous Intermittent RPM * 0 - 83 0 - 101 Peak Torque ** 12,542 Nm (9,250 ft/lb) 14,658 Nm (10,811 ft/lb) Hydraulic Pressure 210 Bar (3,000 psig) 250 Bar (3,600 psig) Maximum Oil Flow 200 litres / min 240 litres / min Pullback: 30000kg @ 2340psi/161Bar 36000kg @ 2810psi/194Bar 52000kg @ 4061psi/280Bar (A10VSO Rexroth Pump Nominal Pressure) 65000kg @ 5076psi/350Bar (A10VSO Rexroth Pump Peak Pressure) Pulldown: 22500kg @ 2340psi/161Bar 27000kg @ 2810psi/194Bar 39000kg @ 4061psi/280Bar (A10VSO Rexroth Pump Nominal Pressure) 49000kg @ 5076psi/350Bar (A10VSO Rexroth Pump Peak Pressure) Survey Winch: *Capacity of 700m of 6mm wire rope. Rod Handling: *KL Rod Handler with hydraulic operation to suit drill pipe up to 4.5" diameter. *Rod Handling Boom, Slew and Raise functions, 4ton winch. *Hydraulic operated Breakout Wrench. Carrier: *Oshkosh Heavy Expanded Mobility Tactical Truck (HEMTT), 8x8, Right Hand Drive. * Detroit Diesel 8V-92TA, 450-hp @2100RPM, liquid-cooled 2-stroke V-8 diesel. * Allison HT740D automatic transmission with torque converter, 4 forward gears/1 reverse gear. * Oshkosh Truck Corporation transfer case, 55000, Air Operated, Front Tandem Disconnect. * Eaton/Oshkosh Differential and Axles 1-RS480, 2-DS480, 3-DS480, 4-RS480. * Drive to the front axles is selectable and all axles have differential locks. * Hendrickson leaf spring with steel saddle, equalizing beams, 254mm vertical travel all round. History: The Hydco 500RC is Manufactured as a High performance Deep hole Drill and is operating around the world. First Manufactured in 1993 the design has undergone many upgrades and is now one of the most powerful drills for its size on the market today. The 500RC is still entirely manufactured at the Hydco Factory in Wangara WA.

Price : POA

DYNATECH (DICD120GR) - TRACK MOUNTED DRILL RIG

DYNATECH (DICD120GR) - TRACK MOUNTED DRILL RIG DOM: 9/2011 SERIAL NO. : E12084-DICD120-0070709 DESCRIPTION INFORMATION Deck Engine: Cummins 6CTA 8.7L Rig/Engine Hours: Low hours (TBA) Accessories: Water injection pump – American Manufacturing Co. AW1122BCD 37GPM @ 1000 psi Location: Queensland (inspection by appointment)

Price : $165,000

*SOLD* BOART LONGYEAR KWL1600 TRUCK MOUNTED DRILL RIG *SOLD*

BOART LONGYEAR KWL1600 TRUCK MOUNTED DRILL RIG DOM: 2011 SERIAL NO. : KWL1600H-2011-13 The KWL1600 is a truck mounted drill rig is a powerful and versatile drill rig that can be utilised for a variety of applications. An excellent drill rig for diamond drilling. When coupled with the KWL rod handler the transition to RC drilling a safe efficient means of handling the heavier drill pipe. This rig and carrier are in very good condition and well presented. Ideal alternative for a new rig buyer looking to get on the job quickly or an update to a current fleet. TECHNICAL INFORMATION DESCRIPTION INFORMATION Deck Engine: CAT C13 silenced enclosure Rig/Engine Hours: 8,613 hours Onboard compressor Not applicable Top Head Drive 3 ½” floating spindle with 70mm bore Drive head side shift Outriggers 4 x encased RHS 107.95mm bore x 1.2m stroke Dump Mast 2m stroke Winch Main haul winch capacity 15,059kg Accessories KWL rod handler Truck DOM: 2010 VIN: WMA96SZZ6BL061506 MAN 41.48 8x8 GVM: 44,000 kg TARE: 31,630 kg Queensland registration: Due 10/03/2018 Odometer: 14,813 klm Compliance status NDT inspection: 06/01/2017 Lifting equipment inspection: 10/12/2015 Service history: Available upon request Location: Queensland (inspection by appointment)

Price : $850,000

Schramm 685 Track Mounted Drill Rig

Schramm 685 Track Mounted Drill Rig DOM: 1996 SERIAL NO. : J124-2712 The Schramm 685 is a heavy duty, heavy hoist, track mounted drill rig. This unit is priced to sell with a Vendor keen to negotiate. TECHNICAL INFORMATION DESCRIPTION INFORMATION Deck Engine: K19 Onboard compressor: Sullair 1150/500 compressor (Serial No. 004-DC5929) Water capacity Approx. 500 litres Accessories: FOPS KL rod handler Rod rack 4 x levelling jacks In mast make/break rod break out system Fire suppression Enclosed operators cabin – air conditioner needs repair History Service history: Available upon request Dimensions Height: 4.6 m Width: 4.0 m Location: Queensland (inspection by appointment)

Price : $390,000

Warman UDR1000 Drill Rig

Warman UDR1000 Drill Rig 1996 Model No carrier, compressor, pump or dump mast

Price : POA

CSD1300L Diamond Coring Rig

CSD1300L diamond coring rig CSD1300L core drilling rig is specially designed for diamond core drilling. Track crawler mounted rig facilitates moving around with great convenience. Robust structure plus strong power supply ensures high penetration rate and outstanding reliability. Its full hydraulic concept includes virtually all operational functions that prevail on the latest models around the world. Specifications: Drilling Capacity Dia of Drill Rod BS,NS,HS,PS Drilling Depth 1,300m 1,000m 700m 400m Hydraulic System Pressure 26MPa Cooling Air Cooled Power System Model Cummins 6BTA5.9 –C180 Type Turbo Charged Power 132KW Engine RPM 2,500rpm Drill Head Max Torque 4,257Nm Max Rotation ,RPM 1,182rpm Feed Stroke 3.5m Max Inside Diameter 117mm Max Pull / Max Push 127KN/ 50KN Main Winch Max Pull 68KN Pulling Speed 28m/min Rope Diameter 16mm Rope Length 30m Wireline Winch Max Pull 11KN(bare drum) Pulling Speed 120m/min Rope Diameter 6.6mm Rope Length 1,000m Mast Length 10m Drilling Angle 45°-90° Dump Length 1.1m Foot Clamp Drill Rod BS, NS, HS, PS Travelling Capacity Max.Permissible Gradient 30° Max.Travelling Speed 2km/h Transporting Dimensions L×W×H 5,100×2,350×2,600mm Total Weight: 8.5t

Price : $265,000

CSD1300G Diamond Coring Rig

CSD1300G diamond coring rig CSD1300G hydraulic rig is specially designed for diamond drilling on ground surface. Track crawler mounted rig facilitates moving around with great convenience. Multi-pressure gauge allows for monitoring working status of the rig systems. Robust structure plus strong power supply ensures high penetration rate and outstanding reliability. The up to date design of hydraulic system makes CSD1300G one of the most favoured models around the world. Specifications: Drilling Capacity Dia of Drill Rod BS,NS,HS,PS Drilling Depth 1,300m 1,000m 700m 400m Hydraulic System Pressure 26MPa Cooling Air Cooled Power System Model Cummins 6BTA5.9-C180 Type Turbo Charged Power 132KW Engine RPM 2,500rpm Drill Head Max Torque 4,257Nm Max Rotation ,RPM 1,182rpm Feed Stroke 3.5m Max Inside Diameter 117mm Max Pull/Max Push 127kN/50kN Main Winch Max Pull 68KN Pulling Speed Low:28m/min High:65m/min Rope Diameter 16mm Rope Length 30m Wireline Winch Max Pull 11KN(bare drum) Pulling Speed 120m/min(bare drum) Rope Diameter 6.6mm Rope Length 1,000m Mast Length 10m Drilling Angle 45°-90° Dump Length 1.4m Foot Clamp Drill Rod BS, NS, HS, PS Travelling Capacity Max.Permissible Gradient 30° Max.Travelling Speed 2km/h Transporting Dimensions L×W×H 5,430×2,300×2,600mm Total Weight 10.3t

Price : $285,000

CSD3000 Diamond Coring Rig

CSD3000 diamond coring rig CSD3000 core drilling rig is specially designed for diamond core drilling. It provides precise control on the drilling capacity. The drill head is designed to slide and dump, together with the full angle rotation structure for drill mast, it effectively reduces manual inputs and improves efficiency. The hydraulic legs are stretchable, which broaden the bearing surface, and ensure outstanding reliability. Its full hydraulic concept includes virtually all operational functions that prevail on the latest models around the world. • 9 meters rod pulling largely improves drilling efficiency due to rod collection frame design on mast • The design of side shift by hydraulic of rotation head largely reduces working tensions and guarantees personnel safety • Multi-pressure gauge reads real time pressures for kinds of major components • High/low speed control of main winch largely meets speed requirements for rods handling • Stepless control of mud pump flow facilitates various drilling needs for mud • telescopic mast greatly reduces working tensions and improves drilling efficiency. • Horizontal extension of jack legs guarantees firm rig standing on the ground. • Its full hydraulic concept includes virtually all operational functions that prevail on the latest models around the world. • Independent tramming cab set in front provides full view for easy rig walking and driver’s safety • Mast dumping guarantees perfect stability during drilling; • Independent hydraulic jacks facilities leveling of the rig; • Great convenience of control of feed pressure; • Standardized parts and components make maintenance and repairing easy; • Real time reading of drilling data on gauges on the control panel; • Mud pump and mixer powered by the rig’s hydraulic system, controlled directly on the rig’s panel; • Top grade hydraulics of European origin; • Experienced engineers plus adequate spare parts ready to provide full service. Specifications: Drilling Capacity Dia of Drill Rod BS,NS,HS,PS Drilling Depth 3,000m 2,300m 1,600m 1,050m Hydraulic System Pressure 28MPa Cooling Air Cooled Power System Model Cummins 6LTAA8.9-C325 Type Turbo Charged Power 239KW Engine RPM 2,200rpm Drill Head Max Torque 8,170Nm Max Rotation ,RPM 1,250rpm Feed Stroke 3,450mm Max Inside Diameter 117mm Max Pull /Max Push 250KN/110KN Main Winch Max Pull 181.44KN Pulling Speed Low:33m/min High:70m/min Rope Diameter 24mm Rope Length 41m Wireline Winch Max Pull 18KN(bare drum) Pulling Speed 150m/min(bare drum) Rope Diameter 6.6mm Rope Length 2,500m Mast Length 11.2-13.7m Drilling Angle 45°-90° Dump Length 1.4m Foot Clamp Drill Rod BS, NS, HS, PS Travelling Capacity Max.Permissible Gradient 30° Max.Travelling Speed 2km/h Transporting Dimensions L×W×H 11,240×2,310×3,330mm Total Weight 23.5t

Price : $460,000

Cubex QXR920 Tracked Drill Rig

Cubex QXR920 Tracked Drill Rig For this you get the rig and any spares we have for it as per spares list. Approximate Hours: 15,000hrs Note: Engine has been removed and used elsewhere. Located in Africa (Mali) Price @$120,000 USD

Price : USD$120,000

Geotechnical Trailer Mounted Drilling Rig - EVH 2100 R

Geotechnical Trailer Mounted Drilling Rig - EVH 2100 R Custom built, based upon an EVH2100 rig. Capabilities:- • Wash bore - (King 2J water swivel) • Auger • SPT • U50 • 3 cylinder diesel engine Currently on dual axle braked trailer (with tool boxes, rod racks, alloyed mud tanks fitted to trailer)

Price : POA

GEMCO H22 TRACK MOUNTED GEOTECHNICAL DIAMOND DRILL RIG

GEMCO H22 TRACK MOUNTED GEOTECHNICAL DIAMOND DRILL RIG STANDARD FEATURES Engine make: Air Cooled Deutz Good Condition Rebuilt 2010 Approx. 12,000hrs Type: BF6L914 Serial Number: 08786209 Power: 99kw Water Pump: FMC W112BCD Other Features: Maximum Power 175HP Maximum Torque Variable Useable Fuel Capacity 400 litres Maximum Feed Force 1,700 psi Maximum Stroke 6.40 metres Maximum Rod Pull 7.50 metres DIMENSIONS Length: 8.30 metres Width: 2.70 metres Height: 4.00 metres Weight: 20.00 tonne Track Size: 800mm x 125mm x 80mm DRILLING CAPACITY CORING – WIRELINE The technical data supplied for drilling depths, has been based on drilling data obtained from operations. The actual drilling depths reached will be dependent upon a number of factors including the rock type, drilling techniques, tools and overall conditions. Drill Rod / Core Barrel Rod Size (mm) Core Size (mm) Hole Depth (metres) PQ 117.5 103.2 200 HQ 88.9 77.8 300 – 350 NQ 69.9 60.3 600

Price : POA

2011 Atlas Copco ROC L7

Atlas Copco ROC L7 details: Hole range 89 mm – 127 mm (3½”- 5″) Hole depth 36 m 120’ CAT C13 Engine 417 HP Hydraulic rock drill COP 4050 54 HP Low hours, excellent condition SERIAL No. AVO 11A1070 / 8992 0071 23 Total Hours Indicated: 3273

Price : $195,000

2003 Atlas Copco L7

2003 Atlas Copco L7 track mounted Hydraulic Drill Rig with ROPS Cab 5 Rod Carousel Hydraulic Breakout Fire Suppression Auto Lube SERIAL No. AVO 03A647/8992 0024 58

Price : $130,000

UDR1000 Truck Mounted Drill Rig

The rig had a major overhaul approx. 4000 hrs There is a 350×900 compressor also available on skid mount which will fit front of Rig Powered by Cummings (very compact unit) 800 hrs showing since new. Set up for diamond drilling

Price : $155,000

UDR1000 Mounted on a 1989 Mann 8×8

UDR1000 Mounted on a 1989 Mann 8×8. A new 1200 head and two W45 Bean triplex pumps on the rig. It also has a 900×350 Sullair air compressor and rod rack on the side. Dump mast and foot clamps. Rig has been completely sand blasted and any repairs required have been completed. The truck has been stripped down to cab, is rust free and fully repainted. Last project was on 1000m NQ diamond drilling but also has capacity of up to 600m of reverse circulation drilling and water well drilling. Has not been used since major overhaul taken place.

Price : $395,000.00

ZDY-100 Diamond Core Drill Rig

ZDY-100 Diamond Core Drill Rig Cummins 6CTA8. 3-C215, liquid cooled, turbo charged, after cooled, diesel engine FMC1122 Mud Pump BRQ – 1325mtrs NRQ – 1053mtrs HRQ – 750mtrs PHD – 535mtrs Location Ex China $USD250,000

2 x BBurg 1600

2 x BBurg 1600 Year 2014 Engine: Deutz Compressor: 30/440 Price: €630,000 ($AUD934,000 ea)

3 x BBurg 1450

3 x BBurg 1450 Year 2013/14 Engine: Deutz Compressor: 10/145 Drill depth 33m Price €504,000 each ($AUD751,000 ea)

6 x Reichdrill C-550-D11

6 x Reichdrill C-550-D11 Year 2014 Engine: Cat C18 Compressor: 1360/375 Pullback 19,750lbs Price €685,000 each ($AUD1,020,000 ea)

Hydco 1200H Drill Rig

Current Hour 731 hours (28/09/16) Model 1200 H Manufacturer Hydco YOM 2009 Engine Cummins Carrier 8x4 Scania Mud/Water Pump FMC Beam Hydraulics Rexroth Electrical System Hydco Drill Head Hydco Tower Hydco Auxiliary Air Fully compatible with all piping & valving installed Auxiliary Mud Fully compatible with all piping & valving installed Depth 1200m HQ Hole Angles 90 degrees Top Speed 100km/h

Price : $395,000

*SOLD*Atlas Copco RD20 XC lll Drill Rig - c/w Rod Presenter, Skull Trailer & Drill Pipe Package*SOLD

Current Hours 3,884 hours Model RD-20 XC III delivered new Apr 2013 Manufacturer Atlas Copco YOM 2012 Carrier 10x6 Custom Crane Carrier– Right hand drive Engine Cummins QSK19C Compressor 350psi / 1250cfm IR Breakouts Cylinder pull Rod Handler Elevators Hydraulics Atlas Copcp Electrical System Atlas Copco Drill Head Atlas Copco RD-20 4SF-2-12 Tower RD-20 18.9m Hydraulic Rod Presenter 45ft Skull Trailer 1200m of 4 1/2IF 9MTR Drill pipe 2,349m of 3 1/2API 9MTR Drill pipe Auxiliary Air Fully compatible with all piping & valving installed Auxiliary Mud Fully compatible with all piping & valving installed Drill String 1200m of 4 1/2IF x 9 MTR drill rods available Hole Angles 90 Degrees Top Speed 80km/h

Price : $1,100,000

EziDrill Single-Pass Blast Hole Drill Rig

Model 15M-SP Serial Number 2016-1-SP-731792 YOM 2016 Engine CAT 3406 (430-HP) Compressor Sullair 1050/100 Depth Capacity 0>15 Metres Pull-down Weight 0>14,500 Kilograms Rotation Speed 0>150 RPM Bit size 200>229 Millimetre (7-7/8” > 9”) Drill Pipe Diameter 178 Millimetre O.D. (7”) Length – Mast Down 21.5 Metres Length – Mast Up 14.10 Metres Height – Mast Do 5.10 Metres Height – Mast Up 20.60 Metres Height – Cab Hand Rail 4.60 Metres Overall Width 5.25 Metres Track Width 3.71 Metres Gross Weight TO BE ADVISED Chassis Weight TO BE ADVISED Mast Weight TO BE ADVISED Tram Speed 3 KPH Drill Bit Breakout Force 3570 Kgs

Price : POA

ERX 10 Tonne Post Hole Lifter (x4 units)

ERX 10 Tonne Post Hole Lifter (4x Brand New Units ready to fit to trucks) Previously been fitting them to 6 x 6 international trucks. All PLC hard and soft ware is IFM and supported Global. Fitting to trucks is possible here in our works.

Price : POA

Brand New F600 & F800 Heli-Man Portable Drill Rigs

3x heli/man portable diamond coring rigs and drilling equipment packages in stock. These ones are built by the end of last year, totally brand new. Light weighed but strong aluminum frame, most up-to-date fabrication workmanship and powerful drilling capacity. We have 2 smaller F600 type and 1 bigger F800

Price : POA

HD-1800 Track Mounted Diamond Core Drill Rig

"Brand New" HD-1800 Track Mounted Diamond Core Drill Rig Comes with the below items as part of the package; 1 set HD-1800 diamond coring rig 2 set NQ CORE BARREL ASSEMBLEY 1.5 MTR 2 set HQ CORE BARREL ASSEMBLEY 1.5 MTR 2 set PQ CORE BARREL ASSEMBLEY 1.5 MTR 1 set NQ EZY LOCK OVERSHOT ASSEMBLY 3 pcs NQ FRONT REAMER STANDARD 3 pcs NQ BACK REAMER STANDARD 2 pcs HQ FRONT REAMER STANDARD 3 pcs HQ BACK REAMER STANDARD 5 pcs HQ IMPREGNATED DRILL BIT 30 pcs HQ DRILL RODS 3 MTR 50 pcs HQ CORE LIFTER CASE 20 pcs HQ CORE LIFTER

Price : (POA)

2012 Coretech CSD1300L Tracked Drill Rig

Coretech CSD1300L Tracked Drill Rig. Machine has only done 1295 hours & cost US$230k in 2012. 2012 CSD1300L, has 1295 hours, comes with1 box of spares

Price : $147,500

*SOLD*UDR650 Drill Rig on 2011 Volvo 8x4 Carrier*SOLD*

UDR650 Drill Rig on 2011 Volvo 8x4 Carrier

Price : $245,000

PRD800 (PRD Max Drill) Truck Mounted Drill Rig on Kenworth Carrier

PRD800 (PRD Max Drill) Truck Mounted Drill Rig on Kenworth Carrier

Price : $255,000

PRD650 Truck Mounted Drill Rig

PRD650 Truck Mounted Drill Rig ONBOARD COMPRESSOR 1100 CFM/ 350 PSI ELGI COMPRESSOR

Price : $205,000