50000L Angle Bottom Tank – DOM 2010 Complete with angle bottom and a split way in center, Manifolds set on both sides to use the tanks as storage and or mixing with capability to stir in any section of the tank. Roll over tarp roof to prevent birds Man hole provides access points for cleaning and confined space regulations are minimized Fold down walkways and aluminium stairs for travel (Stairs hang on end of tank for transport).
Flat Bottom Open Skid Top Tank – 25000 L Capacity – DOM 2010 12000 x 2400 x 1730 (actual depth 1520) 4 x lifting points (each corner) 4 x outlets ( 2 x butterfly valves)
12000 L Skid Mounted Tank with Angle Floor – DOM 2010 7000 x 2250 x 1530 (actual depth 1100) 2 x Butterfly outlet valves Ability to adapt to Hydraulic “Jack Up” with addition of Hydraulic legs in each corner. *Pipe work and fixtures are not included and will be removed prior to purchase*
The SPT Hammer is an effective tool to collect Standard Penetration Test (SPT) blow counts with almost any drill rig. The SPT Hammer is designed as a non-permanent fixture to the rig structure (or permanent if required), and is suspended from your wireline as per the manual SPT Hammer. Features - Complete hydraulic function with fully concealed moving parts - Considerable safety advantages and hands free operation - Designed and manufactured in Australia to comply to all relevant standards - Easily “piggy backed” to any existing control panel - Regular consistent results - Flexibility of non permanent fixture maintained - Interchangeable “thread stubs” allow suitability to all pipe variations - Extremely robust design for long service life As new condition Included are hydraulic hoses, anvil, sub and spit spoon samplers
6 berth Explorex “Exploration” caravans These have only been used on a couple of jobs and are in excellent condition. 2012 builds. 4 x 9kg gas bottles 2 x spare tyres (235/85) Electric trailer brakes 3 x roof mounted reverse cycle air conditioners Fully enclosed wet area in front of van with sink, washing machine and shower Main kitchen with: 2 x upright fridges 2 x upright freezers 4 burner gas stove with oven Sink Microwave Ensuite bedroom off kitchen (concertina doors) with double single bunks Rear sleeper quarters with 2 x double bunks (sleeps 4 in total) Fully enclosed front annexe Satellite TV $114,500.00
This is for the complete package of assets from a decommissioned CNG virtual pipeline inclusive of mother station and daughter station CNG Mother station 5 x CNG compressors 1 x instrument Air Skid 2 x heat exchange module 1x gas control and priority panel 1 x water refrigerative chiller 1 x water refrigerative chiller 4 x truck filling module 1 x motor control centre Daughter station 2 x pressure regulator skid 3 x heater module skid 2 x gas booster compressor – engine drive 2 x scavenge inlet regulator and heating skid 1 x instrument air skid 4 x truck decanting module 4 x truck decanting module 1 x motor control centre Assets are near new Compressors have on average 100 run hours (of 80,000h life) And have been well protected The environment is for the most part dry and warm The compressors have been regularly rotated The mother station systems have been powered and air conditioned since use Water chiller systems have been treated and pumps rotated Pipework is under nitrogen blanket (mother) or low pressure gas blanket (daughter ) Status prior to stopping production The daughter station was fully commissioned and tested The daughter station has now been decommissioned, disassembled and transported to the mother station site The mother station was fully commissioned except the mass filling algorithm which remains incomplete Assets are located Near port headland Western Australia
Silvan 400lt sprayer good condition. New pump which hasn’t done a lot of work.
Explorex Caravan Year: 2011 Layout: 3 bedrooms and an office All rooms air con Condition: Good Located: Western Australia Price: $77,500 ex GST
Jack Up Hydraulic Rod Sloop Make: Gold City Welding Year: 2011 Condition: Good Location: Victoria Price: $33,500 ex GST
FAST AUTOMATED CONTAINER LIFTING For fast, efficient container lifting, look no further than this unit. Capable of lifting all shipping container types, sizes and weights up to 32 tonne, this unit is safe, robust and easy to use. Operated by wireless remote control and with a lift time of just 3 - 4 minutes, this equipment gives you the freedom to lift, load and strip containers at ground level - anywhere, anytime, for less. Lower costs Improve safety Work in new locations Eliminate crane hire Back up your other handling equipment SPECIFICATIONS STANDARD COMPONENTS 4 x automated lift columns 1 x wireless remote control with emergency off-switch 4 x electric cables LIFT CAPACITY 32,000 kg (70,000 lb) LIFT HEIGHT 165 cm (65 in) REVERSING CLEARANCE 40 cm (16 in) LEG WEIGHT 320 kg (700 lb) MINIMUM OPERATORS 1 LIFT SYSTEM Electric powered hydraulics Integrated electronic controls for synchronous lifting Operated by handheld wireless remote CONSTRUCTION High strength steel Quality coatings for corrosion protection Wheeled base with puncture-proof rubber tyres Hydraulic cylinders with integrated counter balance valves POWER SUPPLY 240 VAC 50 Hz / 10 AMPS (other options available) SPECIAL FEATURES Articulated base and stabilising wedges for lifting on uneven surfaces Integrated smartphone app for diagnostics and communicating system information
MOBILE HEAVY CONTAINER LIFTING Now you can transfer heavy containers in any location. Portable and safe, with a lift capacity of up to 32 tonne, this unit is the ideal solution for sites where traditional container handling equipment is too big, heavy or expensive - or simply unavailable. Easy to transport, works on rough ground and can be moved around by one person - no forklift required. Take full control of your container logistics Eliminate crane hire Get heavy containers in and out of remote sites Position containers indoors Make better use of valuable space SPECIFICATIONS STANDARD COMPONENTS 4 x steel legs with carrier frames 4 x double acting hydraulic cylinders 1 x hydraulic power and control unit Assorted hydraulic hoses, fittings & rigging LIFT CAPACITY P32 - 32,000 kg (70,000 lb) P10 - 10,000 kg (22,000 lb) LIFTING HEIGHT 165 cm (65 in) REVERSING CLEARANCE 50 cm (20 in) LEG WEIGHT P32 - 130 kg (286 lb) P10 - 110 kg (242 lb) MINIMUM OPERATORS 2 CONSTRUCTION High strength steel Quality coatings for corrosion protection Hydraulic cylinders with integrated counter balance valves Abrasion resistant hydraulic hoses with quick release couplings Puncture-proof rubber tyres HYDRAULIC POWER UNIT Integrated electric motor, hydraulic pump, oil reservoir and directional control valves, inside steel tube housing on wheeled base POWER SUPPLY 240 VAC 50 Hz / 10 AMPS (110 VAC and DC options available)
With no electronics or hydraulics to maintain, this unit is a reliable performer for sites handling low container volumes. If portability and easy maintenance are your priorities and you have the manpower available, this unit is simple, cost effective and gets the job done. Get containers in and out of remote sites Lower your logistics costs Stop relying on third parties Make your operation independent Position containers indoors SPECIFICATIONS STANDARD COMPONENTS 4 x lifting frames 4 x certified chain hoists LIFT CAPACITY M20 - 20,000 kg (44,000 lb) M10 - 10,000 kg (22,000 lb) LIFT HEIGHT 156 cm (61 in) REVERSING CLEARANCE 40 cm (16 in) LEG WEIGHT 130 kg (286 lb) TOTAL WEIGHT 650 kg (1,433 lb) PACKED DIMENSIONS 222 cm x 113 cm x 70 cm (87 in x 44 in x 28 in) MINIMUM OPERATORS 2 CONSTRUCTION Lightweight, high strength steel Quality coatings for corrosion protection Puncture-proof rubber tyres CHAIN HOISTS Individual chain hoists rated for 50% of system load limit Full force on chain to lift at full load ca. 35 kg (80 lb) Full force on chain to lower at full load ca. 15 kg (33 lb) SPECIAL FEATURES Adjustable base for stability on rough ground Lifting frames disassemble and pack into compact unit Can be transported in container, on truck, or on a ute. Longest component fits inside across width of shipping container.
Komatsu Engine SA12V140 Suit rebuild or parts $14,000.00 ex GST or nearest offer
Sandvik QJ341 jaw crusher - 2012 Hours – 2236 Serial number – SW12643 Engine number – JSC24440 Sandvik QA451 Screener – 2013 Hours – 1431 (This has had a new hour clock fitted) Estimated hours – 3,200 Serial number – SW13258 Engine number – 44609619 Sandvik QE440 Scalper -2014 Hours – 3573 Serial number - 1884BG14116 Engine number – 44415714 Sandvik QJ341 Jaw crusher- 2015 Hours – 2460 Serial number – QJ34100177 Engine number – D9N04899 Sandvik QJ341 Jaw crusher – 2014 Hours – 3150 Serial number – 1886SW14511 Engine number – C9N01390 Sandvik QE341 Scalper – 2013 Hours -2622 Serial number – 1884BG13346 Engine number – 44601134
Wheel loader CATERPILLAR Type: 962 M Year: 2015 Hours: 6.420 - bucket with cutting edge - central lubrication - air conditioner - rear view camera with color monitor - heated and electric adjustable mirrors - full mudguards - tires BRIDGESTONE VJT 23.5R25 - C7.1-Engine with 201 kW
Year/Condition: Brand New Capacity: 35,000 kg Weight of complete set in trolley: 130 kg Compliance: VGM & able to be made Australian Legal for Trade Time required to weigh container Less than 5 minutes Android App: Can be synced to mobile phone Container Compatibility: All container sizes, type and lengths Located: New Zealand Price: AUD $10,700 (Excl GST).
Headworks Trailer • Mining Spec Switchboards control panels • Galvanised Steel or 316 Stainless Steel head works • Free-draining complete with Mudguards • Tandem axle and heavy duty suspension system suitable for in-pit conditions • Trailer braking system and wheel chocks • Conventional tow bar hitch • Front and rear stabiliser legs • Certified lifting lugs • Overhead frame and gridmesh for protection during blasting • Floodlight lamps and Australian standard tail lights, indicators and reflectors • 9kg fire extinguisher
New Holland 8970A Year 2004 Serial #922641 D42285 240 HP 6 Cylinder Hours 6950 approx Gears Forward 16 Gears Reverse 8 Fuel 416L Front Tyres 16.9-30 Rear Tyres 18.4R46 Duels Axle Width 3m Condition needs work – new seat needed, brakes not working, paint faded, Cracked Manifold, full detail
Mine spec cat374d excavator with 1 x bucket 6.5 ton DM 300 rock breaker Model is 2011 Cat 374DL S/N PAS00184 Approx 8000 hours POA
Make : NOT SPECIFIED Model : HVOF Metal Spray Condition: New Brand New, never used. HVOF Metal Spray system. Our Control Console is MP-2100 and the Power Feeder is PF-350
JCB 8025 Excavator & Trailer $40,000 + GST 2016 model Hours 62 Near new condition very low hours traded in on bigger excavator includes half hitch 300mm, 450mm, 1000mm Buckets Ripper & Alloy plant trailer. Also comes with out standing warranty 24mths warranty/ 3000hrs (which ever occurs sooner)
Amazone ZA-M 1501 Fertillizer/Manure spreader $12,089 + GST Twin disc spreader 1500 Litre hopper capacity folding hopper cover Filling sive to stop foreign objects 540rpm PTO shaft 1 3/8" 6 spline c/w shear bolt protection 36M spreading disc measuring bucket and calibration chart Saftey set (includes guard lube, traffic lights and warning signs)
Year: 2006 Condition: good Brisbane, Queensland $13,750 ex GST no re inspection $23,750 ex GST with re inspection
PVC Casing - 80mm PN18 Slotted 6mtr PVC Casing (x52) @$50 ea ex GST - 80mm Class 18 x 6mtr (x3) @$35 ea ex GST
20FT Accommodation Container. Perfect for a granny flat or for rural accommodation. Included in the price is; - 20ft unit with king single bed (new mattress) - toilet, shower and vanity - kitchenette with bar fridge - desk and chair - TV with coaxial cable - Split system AC and HWU - Lot of storage draws and cupboards (lockable). - Units are 2011/2012 build and are in as NEW condition - All units come with an electrical and plumbing certificate.
Sandvik Rhino 400H Raise Bore Machine Year: 2006 Guide hole diameter: 229 mm, Diameter of reamer:1 500-1 800mm, Maximum drilling depth :400 m, Working torque:75 kN, Maximum torque:99 kN, Hole tension :1920 kN, Drill pipe diameter :203 mm, Drill pipe effective length:1 220 mm, Total power of host:100 kW The monitoring instrument: Fle-ITG inclinometer
2010 Model BOP and Accumulator Shack "Unused" BOP and accumulator shack, brand new in 2010 and has never been used. Certs currently are out of date, client has all the test certificates and operation manuals. • BOP Hydraulic Control Module o Model – FKQ320-4 o Serial Number – 201009-13-07 o Manufacturer – TIEHU PETROLUEM MACHINERY CO, LTD o Inspection Date – 10/10 2010 • BOP Annular Preventer o Model – FH28-35/70 9”- 3000psi o Serial Number – 201005-84 o Manufacturer – TIEHU PETROLUEM MACHINERY CO, LTD o Inspection Date – 17/6/2010 • Hydraulic Single RAM BOP o Model – FZ28-70 9”- 5000 psi o Serial Number – 201005-85 o Manufacturer – TIEHU PETROLUEM MACHINERY CO, LTD o Inspection Date – 17/6/2010 • Cross Joint/Spool o Model – FZ23-35 9”- 5000 psi o Serial Number – 201005-86 o Manufacturer – TIEHU PETROLUEM MACHINERY CO, LTD o Inspection Date – 17/6/2010 • Choke Manifold o Working Pressure – 10,000 psi o Main Bore Size – 3 1/16” o Outlet Size – 3 1/16” o Temperature Class – PU o Material Class – EE – 0.5 o Product Specification – PSL3 o Performance Requirement – PR1 o Manufacturer – SHANGHI SHENKAI PETROLEUM EQUIPMENT CO, LTD
T161 Platform & Header, Drawbar Trailers (Cometto) 2x 6 axle units 1600mm Spacing 3460mm Wide 825 x 15 tyres Year 1975 Gross per line: 32 tonne Net Per line: 28 tonne 6 Axle Lines Registration J336P Spoked Axles Male-Male Joint Price @$180,000 NZD ea ex GST T161 Platform & Header, Drawbar Trailers (Cometto) 1x 3 axle unit 1600mm Spacing 3460mm Wide 825 x 15 tyres Year 1983 Gross per line: 32 tonne Net Per line: 28 tonne 3 Axle Lines Registration L123PP 6 Spoke Axles Male-Female Joint Price @$90,000 NZD ex GST Located: New Zealand
24 Volt DC Voltage Self Contained Rooftop Air Conditioner With Cooling power of 6Kw makes this unit suitable for heavy duty applications. The DRK-9727 is a fully self-contained Air Conditioner unit available in 24 volt. Rencool modifies the RedDOT unit to suit the needs of the 24 volt Air Conditioning DC Voltage Compressor. Ideal for applications for when the conventional pulley drive setup is not an option. Quick easy Installations, no long hose runs, use while engine on or off makes this system configuration the best solution when it comes to an instant cooling application. The 9727 sets the standard Condition: New
Mobile Workshop / Office 20ft Rig Container / workshop and spare parts for rig
330kva gen set V-92 Detroit Diesel modular series (May 1982) 330 kva with 61 hours Lincoln industrial radiator (new core 6 months old $1200) 2 x batteries 220ca new on 10/2016 500+ ltr remote fuel tank, in potable spill tank. About 10 mtr of cables for hook up to switch board. Regularly serviced, Weight 3 ton A little bit dusty from factory strip out, currently running condition